Flange Joint Sealing: Selection, Installation, and Why Joints Keep Leaking

A flanged joint is a system, not a component. How to select a gasket based on the medium and PN/DN, follow the correct installation procedure, and identify the cause of recurring leaks.

Flange Joint Sealing: Selection, Installation, and Why Joints Keep Leaking

A flanged joint is a system: flanges, bolts, gasket and installation procedure. A leak is almost always a system failure, not a component failure. That’s why replacing the gasket with a “better” one so often doesn’t help.

Three conditions for a leak-tight joint

  1. Sufficient gasket stress – the bolts must compress the gasket enough to seal flange surface irregularities and withstand the pressure of the fluid.
  2. Stress below the material limit – an overloaded gasket will crush or extrude from the joint.
  3. Stress maintained throughout operation – gasket seating, temperature cycles and bolt relaxation reduce preload.

Joint design balances points 1 and 2. Point 3 is managed during operation.

Selecting a gasket

By fluid – chemical resistance is a decisive selection criterion. Aggressive fluids: PTFE (POWERflon). Steam and high temperatures: graphite (POWERgraf). General service: compressed fibre (POWERgasket). Check compatibility with the specific chemical in the chemical resistance database.

By temperature and pressure – compressed fibre up to 150 °C, PTFE −268 to 260 °C, graphite −200 to 450 °C, mica up to 900 °C. Cut flat gaskets up to 40 bar; above that, use spiral-wound, camprofile or metal gaskets.

By flange condition – camprofile or expanded graphite gaskets can accommodate damaged surfaces. Better still: repair the surfaces (flange resurfacing).

By DN/PN – with large nominal diameters and low pressure ratings, the bolts often cannot generate the required gasket stress. Solution: Improving the leak tightness of DN PN flange joints.

The installation procedure determines the result

  1. Clean and inspect the surfaces – check for gasket residue, corrosion and flatness.
  2. Inspect and lubricate the bolts – use a lubricant with a defined coefficient of friction. Without it, actual preload is a lottery, with variation of over ±30 %.
  3. Centre the gasket – do not glue or lubricate it.
  4. Tighten in a cross pattern in 3–4 steps: 30 → 60 → 100 % of the torque, followed by a final pass around the circumference.
  5. Retighten after start-up as specified for the joint.

The specified torque is calculated for the specific joint – gasket, bolts, lubricant and fluid. That’s exactly what we do with our bolt tightening torque calculation service; you can find a table in the article Bolt Tightening Torques.

Repeated leaks: where to look for the cause

We take a systematic approach to problem joints: comprehensive leak-tightness solutions for flange joints – analysis, calculation, installation and a guarantee.

Resolve a problem joint →

Which gasket should I use for a steam flange joint?

Expanded graphite – withstands 450 °C and steam cycles. For less demanding conditions, use a high-quality compressed fibre sheet.

Why is the joint still leaking after replacing the gasket?

The cause usually isn’t the gasket: insufficient or uneven preload, damaged surfaces, joint relaxation or an unsuitable design for the DN/PN.

How should I retighten a flange joint?

Use a cross pattern, tightening in 3–4 steps to the calculated torque, with lubricated threads and a defined coefficient of friction.

Can a damaged flange surface be repaired without dismantling it?

Yes – flange resurfacing is carried out by machining the surface in place.

Are you ready to put your seal selection worries behind you? Contact us

and get valuable advice and information on industrial seals

Logo Pokorny Industries

Pokorny Industries Partnership in quality

All prices excluding VAT

© Pokorny industries s.r.o. 2026 - all rights reserved

Made by servisdesign