Types of Industrial Seals: An Overview and How to Choose the Right One

Flat, spiral-wound and camprofile gaskets, packing, oil seals and O-rings. The limitations of each type and the mistakes we see most often in industrial settings.

Types of Industrial Seals: An Overview and How to Choose the Right One

Leaks aren’t caused by “bad gaskets.” They’re caused by gaskets selected for conditions they weren’t designed to handle. This guide covers the main types of industrial seals, their limits, and the mistakes we see most often in operating facilities.

Static vs. dynamic seals

The first question to ask when choosing a seal isn’t “what material?” but “does it move?”

Static seals seal joints with no relative movement: flange joints, vessel covers, threaded connections. They include flat, spiral-wound, camprofile and metal gaskets.

Dynamic seals seal moving components: rotating pump shafts, agitators and piston rods. They include mechanical seals, packing and oil seals.

Mixing up these two categories is the fastest way to cause an outage. A static seal on a rotating shaft will fail within hours.

Static seals

Flat gaskets

The most common type. They’re cut from gasket sheets, and their properties depend on the material:

MaterialOperating temperatureTypical applications
Compressed fibre sheets (aramid + NBR)−40 to 150 °Cwater, steam, oils, gases
PTFE (Teflon sheets)−268 to 260 °Cchemical processing, food processing, pharmaceuticals
Expanded graphite−200 to 450 °Csteam, high temperatures, power generation
Expanded mica100 to 900 °Cflue gases, extreme temperatures
Rubber (NBR, EPDM, FKM, silicone)−60 to 200 °C depending on typelow pressures, water, air, food

We generally use die-cut gaskets up to 40 bar. Above that, metal gaskets are the way to go—or get in touch for advice.

Common mistake: choosing based only on the temperature of the medium. Chemical resistance and the actual clamping pressure in the joint are more often what determine whether a gasket fails.

Spiral-wound gaskets

Made from alternating layers of a metal strip and a soft filler (graphite, PTFE). They withstand high pressures and temperature cycling, making them suitable for refineries, chemical plants and power generation. However, they need to be tightened sufficiently; insufficient torque is a common cause of leaks.

Camprofile gaskets

A grooved metal core with a soft layer on both sides. They combine the strength of metal with the conformability of a soft material. They’re the first choice for heat exchangers and joints subject to fluctuating loads—and can even accommodate flanges in less-than-perfect condition.

Metal gaskets

For pressures and temperatures beyond the capabilities of soft materials. They require precisely finished sealing surfaces and high bolt loads.

O-rings

The simplest and least expensive sealing element—provided the size, material and groove are right. They almost always fail because of the wrong material choice or incorrect installation: twisting or damage against the edge of the groove.

Thread sealants

PTFE tape, cords and anaerobic sealants. The right choice depends on the medium, temperature and whether the joint needs to be dismantled.

Dynamic seals

Mechanical seals

The standard for rotating pump and agitator shafts. Two lapped faces slide against each other on a thin film of the medium. A single seal is used for standard applications; a double seal with a barrier fluid is used for toxic, flammable or crystallising media.

Common mistake: replacing the seal without addressing the cause of the failure—misalignment, vibration or dry running. The new seal then ends up just like the old one.

Packing

Braided packing (graphite, PTFE, aramid) compressed in a stuffing box. It can handle harsh operating conditions and abrasive media, and is designed to allow controlled leakage. Where leakage is unacceptable, use a mechanical seal.

Oil seals

A rubber lip that seals against a shaft—the standard solution for retaining oil in gearboxes and bearing assemblies. Service life depends on the condition of the shaft and on correct installation: a damaged lip or dry start-up can cause a leak within days.

Sealing profiles

Rubber profiles for covers, doors and large static seals. We vulcanise them into custom, endless frames.

Four questions that determine the right choice

  1. Movement – is the joint static, or does it rotate?
  2. Medium – what exactly are you sealing, including its concentration? Check compatibility in our chemical resistance database.
  3. Temperature and pressure – operating values, including peaks and cycles, not just the values on the nameplate.
  4. The joint itself – flange condition, bolt load and tightening torque. Even the best material can’t seal a poorly designed joint.

If you’re not sure, ask before installation. It’s cheaper than dealing with an outage.

Choosing the right seal is half the job. Installation is the other half.

We don’t just sell components—we deliver leak-tight joints: analysis → calculation → supply → installation → guarantee. When we design and assemble the joint, we stand behind the result.

Get advice on choosing a seal →

Are you ready to put your seal selection worries behind you? Contact us

and get valuable advice and information on industrial seals

Logo Pokorny Industries

Pokorny Industries Partnership in quality

All prices excluding VAT

© Pokorny industries s.r.o. 2026 - all rights reserved

Made by servisdesign