Bolt tightening torque: chart, calculation, and common mistakes

Reference table of torque values by bolt size and strength class, the effect of lubrication—and why the table does not apply to flange joints.

Bolt tightening torque: chart, calculation, and common mistakes

Tightening torque is one of the most frequently estimated values in maintenance—and the tightness of every joint depends on it. Here’s a reference table, an explanation of what torque actually controls, and where a table is not enough.

The goal is not torque, but preload

Torque is just an indirect way of achieving preload—the force with which a bolt clamps a joint. Friction comes between the two: roughly 90% of the torque is lost in the threads and under the bolt head, and only ~10% is converted into preload.

Two identical bolts tightened to the same torque—one dry, the other lubricated—will produce completely different preload. The difference can be tens of percent. Without a specified lubricant, torque is just a number.

Reference torque table

Metric thread, friction μ = 0.14, 90% of yield strength used.

Bolt8.810.912.9
M610 Nm15 Nm18 Nm
M825 Nm36 Nm43 Nm
M1049 Nm72 Nm84 Nm
M1285 Nm125 Nm145 Nm
M16210 Nm310 Nm365 Nm
M20425 Nm610 Nm710 Nm
M24730 Nm1 050 Nm1 220 Nm
M301 450 Nm2 100 Nm2 450 Nm

The table applies to bolts. It does not apply to flanged joints with gaskets—there, the torque is determined by the gasket, not the bolt.

Why torque is calculated for a flanged joint

Gaskets have their own limits:

The correct torque is the range where all three requirements overlap, with an allowance for preload losses in service. The calculation takes into account the gasket type, bolts, lubricant, pressure and temperature. No online table can do that, which is why we offer a tightening torque calculation with a report for your specific joint.

Lubricant: the most overlooked variable

A lubricant with a defined coefficient of friction is essential for repeatable results. We use dry lubricants with measured friction values—so installers tighten to a torque that matches the calculation. Bonus: the bolts can still be loosened years later (seized bolts).

Five common mistakes

  1. No torque wrench—you can’t get within ±50% by feel.
  2. No procedure—tighten in a cross pattern, in 3–4 steps (30 → 60 → 100 %).
  3. Dry threads—undefined friction means undefined preload.
  4. Using the old torque for a new gasket type—different material, different calculation.
  5. No retightening after startup where the material requires it.

Confidence instead of a table

For critical joints, we calculate the torque, supply the lubricant and train installers—or assemble the joint ourselves and guarantee its tightness. Analysis → calculation → supply → installation → guarantee.

Order a torque calculation →

What torque should I use for an M12 grade 8.8 bolt?

As a guide, 85 Nm at μ = 0.14. For a flanged joint, the torque is determined by the gasket—the value is calculated for the specific joint.

Do bolts need to be lubricated?

Yes, with a lubricant that has a defined coefficient of friction. Without it, the relationship between torque and preload is unpredictable.

Why tighten in a cross pattern?

It ensures even compression. Tightening around the gasket’s perimeter can cause it to buckle and lead to local leaks.

When is a table not enough?

Whenever the joint includes a gasket, is subject to thermal cycling or contains a critical medium.

Are you ready to put your seal selection worries behind you? Contact us

and get valuable advice and information on industrial seals

Logo Pokorny Industries

Pokorny Industries Partnership in quality

All prices excluding VAT

© Pokorny industries s.r.o. 2026 - all rights reserved

Made by servisdesign